Product Center

turntable platter bearing diy in slovakia

images

Design Philosophy For Turntables: A Paper From Pierre Lurne Of …

13/1/2022· In most turntables, the platter is supported by a bearing point at the end of a long spindle that is mounted on the platter and sticking well below it. The bearing remains on the chassis. This usual and conventional bearing, intensively used by Thorens, Linn and so many other brands, can provide positive results but quickly reaches obvious limitations.

images

Holbo Airbearing Turntable | Hi-Fi News

4/9/2020· An air-bearing turntable and a parallel-tracking, air-bearing tonearm in a single, easy-to-use package for under £7000? Devotees of both will love the Holbo Airbearing Every product type has its following, however focused. I am sure, for example, that there are devotees of hybrid amps with tube front-ends and solid-state output stages just as, among the niches in LP …

images

Delrin Platter - groove tracer

The Delrin platter carries more mass than the original glass platter, 83 ounces compared to 70 ounces for the glass platter. This increases its ability to maintain constant rotational speed. The extra mass will not damage the bearing. The outside diameter of the platter is recessed and is 5/8” (15mm) larger than the original platter to

images

My DIY Turntable

20/10/2021· The platter is from VPI, the 2" thick aluminum version sold as an upgrade for the Classic and some other tables. It has an inverted bearing and is less heavy than the one I''d used before. The aroards in the photos are temporary, the one on the right being African teak; the other is just pine.

images

: rotating plate

Erfo 16Pack Lazy Susan Turntable Bearings Hardware, 4 Inch Square Swivel Plate, 5/16-Inch Thick Rotating Plate Replacement Parts for DIY Lazy Susan Project Kitchen Storage Rack Serving Trays. $25.95. $25.

images

Platter bearing maintenance - Lenco Guides

May 23, 2021 - Platter bearing maintenance. Bearing overview: [html] Bottom cap/Plastic cap Bearing housing/Turntable spindle bearing Bearing housing flange Spindle Spindle locking screw/Special scr

images

DIY turntable spindle bearing tutorial | Page 5 | diyAudio

24/5/2015· Sing of platter isolation from the bearing, here''s an extreme example from the recent Munich 2015 High End show. The Physical Emotions Caeles turntable ''s top platter is separated by three spikes from the bottom thicker platter. You can''t get more isolated

images

Diy magnetic turntable platter bearing ( one point levitation …

9/11/2017· The 5 outer magnets center the tube and reduce the weight acting on the sapphire / pivot.A drawing is at the end of the video.

images

Platter bearing maintenance - Lenco Guides

May 23, 2021 - Platter bearing maintenance. Bearing overview: [html] Bottom cap/Plastic cap Bearing housing/Turntable spindle bearing Bearing housing flange Spindle Spindle locking screw/Special scr When the auto-complete results are available, use the up and

images

DIY turntable spindle bearing tutorial | diyAudio

19/2/2015· Hy everyone, I would like to open a new tutorial for people like me who want to make his own diy turntable spindle bearing avoiding waste too much time on bed working experiments. As a standard bearing I suggest the bearing of the following image

images

Pyon Sound turntable bearing | Diy turntable, Diy audio …

Pyon Sound turntable bearing. Find this Pin and more on Audio equipment by Rob Rofman. Diy Turntable. Audiophile Turntable. Hifi Video. High End Turntables. Turntable Cartridge. High End Sers. Sound & Vision.

images

Pyon Sound turntable bearing | Diy turntable, Diy audio …

Pyon Sound turntable bearing. Find this Pin and more on Audio equipment by Rob Rofman. Diy Turntable. Audiophile Turntable. Hifi Video. High End Turntables. Turntable Cartridge. High End Sers. Sound & Vision.

images

TONEARMS, upgrades, parts.au for advice on a turntable to meet your

images

Deep Run Design Audio Products

This is a platter bearing assely designed for the DIY turntable builder. It may be offered in several materials and certainly in several configurations, depending on the platter interface. It''s based on the very heavy duty bearings used in the professional broadcast turntables of the past like Empire and Rek-O-Kut models.

images

DIY Turntable - Graham Slee Audio Forum | HiFi System …

4/8/2012· The main mechanical components are from several donor turntables including the platter and bearing, DC motor, and Jelco tonearm. The handmade plinth is from 2 layers of finger jointed Beech separated by soft rubber pads. The motor is attached to the bottom layer while the platter bearing and tonearm are attached to the top layer.

images

10 Best Turntable Isolation Platform - Fifth Geek

15/12/2019· The Best Turntable Isolation Platforms The following are some of the best turntable isolation platforms available: Gingko Audio Cloud 11 Vibration Control Platform This turntable isolation platform may look pretty simple when it meets the eye. However, it has been

images

Turntable kit Instructions

Platter & Sub-platter Main bearing house bottom nut & ¾” UNF top nut + bearing house plate (fitted on complete standard kit) Standard Motor & fitted short pul ley - 3 off M2 x 6mm motor screws in bag, 2mm A/F Allen key Power supply 230 volt or 110 volt

images

My DIY Turntable

20/10/2021· The platter is from VPI, the 2" thick aluminum version sold as an upgrade for the Classic and some other tables. It has an inverted bearing and is less heavy than the one I''d used before. The aroards in the photos are temporary, the one on the right being African teak; the other is just pine.

images

VPI Scout 11.5" Platter and Bearing DIY Turntable | eBay

Details about VPI Scout 11.5" Platter and Bearing DIY Turntable VPI Scout 11.5" Platter and Bearing DIY Turntable Item Information Condition: Used Price: US $500.00 $43 for 12 months with PayPal Creditopens a installment calculator layer* $43 for 12

images

turntable – DIY Hifi Supply

2/2/2013· Kit 1 : Bearing + Spindle, $391, save $44. Kit 2 : Kit 1 + Platter + Belt, $641, save 114. Kit 3 : Kit 2 + Plinth and foot, $998, save $217. Kit 4 : Kit 3 + Tonearm, $1531, save $374. Kit 5 : Kit 4 + Magnetic Levitators, $1650, save $415. You may order individual parts under egory Turntable Parts.

images

DIY turntable build | Electronics Forums

8/7/2012· 1. Construct using wooden plinth, custom motor. 2. Steal (not literally) tone arm assely, needle / cartridge and pre-amp board from existing turntable (potentially find broken one on eBay or the like) 3. Pitch control into table at +/- 8-10%.

images

Delrin Platter - groove tracer

The Delrin platter carries more mass than the original glass platter, 83 ounces compared to 70 ounces for the glass platter. This increases its ability to maintain constant rotational speed. The extra mass will not damage the bearing. The outside diameter of the platter is recessed and is 5/8” (15mm) larger than the original platter to

images

A DIY Turntable Project | Virtual Listening Room

1/1/2007· Since I had a stainless slab for a platter, I asked if they could have their machinist make one for me and if their inverted bearing would handle the 75 lb platter weight. David Fletcher, the designer of the original Sota table design still consults for SOTA, so after checking with him, I was told the bearing would properly handle a platter weight up to 100 lbs.

images

DIY Turntable Project - The Analog Dept

Any old turntable can be used for parts, key things to look for are a quality platter bearing and preferably if the platter bearing housing is fitted with screws. I selected wood to construct the new turntable and the main reason is the fact that I have the means to work with wood.

images

The Oil Rig Turntable: The Turntable

After coming ac ross some DIY efforts at building turntables, I too d ecided to give it a try… For the turntable, I went for an all aluminium construction and a decidedly “mechanical” look. The frame consists of 2 aluminium sheets strongly bolted together, and the platter is a “sandwich” of aluminium-acrylate-aluminium epoxyed toge ther for some vibration dampening.

images

10 Best Turntable Isolation Platform - Fifth Geek

15/12/2019· The Best Turntable Isolation Platforms The following are some of the best turntable isolation platforms available: Gingko Audio Cloud 11 Vibration Control Platform This turntable isolation platform may look pretty simple when it meets the eye. However, it has been

images

Sati Turntable - Hørning Hybrid Systems

Later in history came high tech bearing variations like the air bearing and the magnet bearing both used to raise the turntable platter in order to archive minimal Friction. With the development of air floating platter has the industry obtained the highest isolation from the turntables Ground.

images

Auto-return and auto-start- Vinyl Engine - Vinyl Engine | The Home of the Turntable

9/4/2020· 2) the platter design, 3) the platter bearing design. Again I''m basing these impressions on my own experience working on so many turntables in the last couple of years. The older stacking turntables from the late 1950''s into the mid to late 1960''s may be and expection along with some very low low end turntables from the 1970''s - the 1990''s.